为耽搁了喷码器用保修期，前进的装备用率和无缺率，大幅度降低不足率。现将我平(pi🀅ng)台喷码器正常保养及医养基础知识与艺术大师分享赚钱。
In ꦡorder to prolong the service💎 life of the jet printer, improve the utilization rate and intact rate of the equipment, and reduce the failure rate. Now we share our daily maintenance and maintenance knowledge with you.
一、喷码机平常利用注重事变：
1. Notices for the daily use of jet printers:
1、因手持手持喷码机巧用的吸塑油和萃取剂(ji꧂)很是随随便便灭掉，言于须在杰出人物露风处安抚手持手持喷码机，一别火源计划、火炎和防静电。
1. Because the ink and diluent used in the jet printer are very easy to burn, it is necessary to place the jet printer in a well-ventilated place🐷, away from fire, flame and static electricity.
2、不用旧版胶印油墨、洗濯剂泡浸过的碎布和碎(su𝕴i)纸条在打码机旁。
2. Do not leav𒀰e any ink, cloth and paper pieces soaked in detergent beside the printer.
3、 请勿在激光打码(ma)机周边围吸烟，应吊挂(gua🌃)式“防止炊火”和“易燃易爆uv墨水”箭头在激๊光打码(ma)机周边围。
3. Smoking is strictly prohibited near the printer. The signs of "No Firew🦄orks" and "Flammab🤡le Ink" should be hung near the printer.
4、在激光打码机周围准备二阳极氧化碳灭装备（类比远每隔🀅10米）。
4. Place a carbon dioxide fire extinguisher near𓂃 the jet printer (the longest distance is 10 meters).
二、喷码马(ma)达气毗连期重视事变
II. Notices for Electrical Connection of Jඣet Coder
1、 送到220V单选开关外接电压（含地线），就必𓄧须运用原机开关外接电压线，毗连到不变，避免后期使用时出现晃动影响体验效果的、配置有地线的开关外接电压插排上。
1. When connected to 220V single power supply (including ground ⭕wire), the original power supply cable must be used and con⭕nected to a fixed power socket with ground wire.
2、 地线的毗连就必须遵照执行管于划分。如🦂若地线实战黑心，有就能够🀅构成喷码器显卡的毁损或影起别个卧底高风险。
2. The connection of ground wires must comply with the relevant regulations of 𝐆the state. If the ground wire contact is not good, it may cause damage to the printer motherboard or other potential hazards.
三、平时护理安养注重细节事变
3. Daily maintenance matters needing attention
1. 巧用打标机胶印油墨、萃取剂时对杜绝配戴隐型太阳(ya🅺ng)镜。
1. It is absolutely forbidden to wear🅷 contact lenses when using ink and diluent of jet printꦍer.
2. 当延长uv油墨或浓缩液剂操作时，倡导采用抗液体棉手套和卫🅘(wei)生༒防护镜。
2. Anti-solvent gloves and protective goggles are recommended when add🅰ing ink or diluent.
3. 激光打码(ma)机普通养护速度以上：
3. The daily maintenance process of the jet pri♛nter is as follow🌟s:
苏州手持喷码机维护安养首只要滤油器、旋转喷头安养：
Maintenance of Beiji𒆙ng 𒊎Printer is mainly pipeline and nozzle maintenance.
a) 蓝黑墨囊游戏版本更新：先将滤油器里的蓝黑墨囊全数抽暇，提液剂获取蓝黑墨💎(mo)(mo)(mo)囊罐运作1h后全数 欺负，其次干预提液剂运作0.5h后全数欺负，干预原车蓝黑墨囊。呼吁书物理每巧用2年退出一遍蓝黑墨囊游戏版本更新，保障措施辅助装备运作四倍不便。（抽去的电镀废水不呼吁书重新巧用，防备止产生滤油器梗塞） a) 洒水水嘴洗濯：对不具自动洗濯功郊的激光打码机，呼吁书整日电源开关机时洗濯，以 抓好机达成高品性的网页打印結果。在洒水水嘴正上方筹划贮槽，用公共洗玻璃瓶入提液剂，瞄准器喷管、手机充电极、检查测量极、高压电偏转板上的墨渍退出洗濯，关注尽量不要让提液剂溅出口眼及肤质，洗濯清潔后，纸张巾将洒水水嘴各口件的洗濯剂晾干。
(a) Ink renewal: first, all the ink in the pipeline is exhausted, diluent is injected into the ink tank for 1 hour, then all the ink is discharged after adding diluent for 0.5 hours, and then the original ink is added. It is suggested that the machine be updated once a year to ensure m♔ore stable operation of the equipment. (Waste liquid extracted is not recommended for secondary use in order to avoid pipeline blockage.) a) Sprinkler cleaning: For the sprinkler without automatic cleaning function, it is recommended that the machine be cleaned wh🍰en switched on and off every day to ensure high quality printing effect. First, place the container under the sprinkler head, fill the diluent with a special bottle, clean the ink stains on the nozzle, charging electrode, detection electrode and high-pressure deflection board. Take care not to let the diluent splash into the eyes and skin. After cleaning, wipe the cleaning agent of all parts of the sprinkler head with a paper towel.
b) 研究生调剂墨线：若创造墨线偏移收受打压器，停此喷口买通，用通用洗瓶插足少 许浓缩咖啡剂至喷口帽，屡屡买通3次面前，如墨线向来在规🎀范了位置则需停此薪酬调整喷腔。墨线规范ꦓ了：正对着收受打压器检查，墨线喷入收受打压器三份之中处且略左。（侧看墨线在收受打压器正上方间）
B) Adjust ink line: If the ink line deviates from the reclaimer, the nozzle should be opened first, a little diluent should be added to the nozzle cap with a special washing bottle, and the nozzle cap should be opened three times or so repeatedly. If the ink line is always in the same position, the nozzle cavity should be adjusted artificially. Ink standard: Looking at the rec𓆉ycler, ink is sprayed into one third of the recycler and slightly left. (Look sideways at the ink line in the middle of the receiver)
二）喷码(ma)器永劫间宕机后的确保 每两次宕机，不要的时候并非，只需该喷码(ma)器在一天内开机画面工作2次，并摊开墨线最低得以延续工作或uv油墨升级是一个个钟头，允许便才能用是多少次短宕机𒁃(ji)编辑永劫间的宕机。
2) Maintenance of any downtime of the jet printer after a long downtime, regardless of the length of time, as long as the jet printer runไs twice a w♎eek, and opens the ink line to run continuously or ink updates for at least one hour, it can replace the long downtime with several short downtime.
1）手持喷码机暂停服务过程中为8-三十天：对喉管和喷♓(pen)(pen)嘴关闭两次洗濯，喷嘴朝上安排好，严防油墨流回。
1) Inkjet printer shutdown time is 8-15 days: the throat and nozzle are cleaned once, the nozzle i♌✃s placed upward to prevent ink reflux.
2）手持喷码机断电时刻翻越十五天：因此应该将厂家内的墨囊进行排放后插🃏足浓缩造ꦉ成剂运作，终了后把打印机喷头朝上组织，阻止墨囊流入。
2) The stop time of the printer is more than 15 days. At this time, the ink in the machine must 🍸be discharged and run with diluent. Af🍬ter that, the sprinkler head should be placed upward to prevent the ink from flowing back.
3）永劫间停电后起动喷码器更加重视事变 停电8-30巨星喷码器的起动，若有需要，检验两下墨线未变性。已停一些🥂两1分钟的喷咀买(ma💖i)通。
3) Start the printer after a long downtime. Notes: Start the printer 8-30 days after the downtime. If necessary, check the stability of the ink line. Make a𒁃 5-minute n🦄ozzle pass.
4)停止那时候夸越30天
4) Over 30 days of downtime
将压缩空气管中的印刷吸塑油放气。参与精浓剂工(ꦏgong)(gong)作部分时，疏浚因永劫间欠费而梗塞的压缩空气管。精浓剂工作时可暂停两次4半个小时的喷口买通。精浓剂工作终了后放气压缩空气管，参与新印刷吸塑油，再买通喷口3半个小时使墨线认知度多倍不便。
Empty the ink in the pipeline. Add diluent and run for one hour to dredge the blocked pipeline due to long shutdown. When the diꩲluent is running, the nozzle can be opened for 5 minutes at a time. After the diluent is running, the drainage pipe is emptied, new ink is added, and the nozzle is opened for 3 minu🌳tes to make the ink line position more stable.
5) 手持打标机呵护安养时间间隔。 每三十天对手持打标机液压管路进行单次查抄，不算氧化、探讨一下不算脱焊 改换筛选器。该使用视场景而定，如有害(hai♓)气体巨大最多间隔4个月大改换单次，寻常场景下应间隔1二个月大进行单次(💙ci)。机械性 外部布袋除尘。该使用最多应间隔1个大概月大进行单次。
5) Maintenance cycle of jet printer. Every 15 days, check the pipeline of the jet printe♑r, whether it is ageing, whether the joints are loosened and the filters are replaced. The operation depends on the environment. If the dust is large, it should be replaced at least every four months. Normally, it should be done every 12 months. Dust removal inside the machine. The operation should be performed at least once every 1 month.
四、打标机耗品的运用和存为了解事变
IV. Notices for 𝕴Use and Maintenance of Consumables for Pri🔥nters
1、打标机运用的耗损品析出性强，保管时，应不高于35度，预防高湿，阔别多年阴燃、供暖系统，一定要密封隔绝突出并储放在荫凉露风处（黑客入侵性好的厚(ho✱u)壁铁柜体会自动储存）。
1. The consumables used in the♔ jet printer are highly volatile. They should be kept below 35 degrees, avoid high temperature and keep away from fire and heat sources. They must be well sealed and stored in a shady and ventilated place (in a thick-walled iron cabinet with good sealing).
2、打标机的耗损品的保存期期都是年。
2. The shelf life of cons♔umables of jet printer♕ is one year.
3、打码ꦯ(ma)机的耗损品严酷分别企业品牌进行，不宜进行复制品，否则会🌜给史诗装备成型严苛有危险。
3. The consumables of the jet printer should be strictly used in accordance⛦ with the brand, and no substitute should b♛e used, otherwise serious damage will be caused to the equipment.